What did you do to your bike today ??

Post by **Monty** » 24 Apr 2016, 19:30

2 hours in the freezing rain and at one point horizontal sleet! Not by choice, the Disco is playing up and we can't fit the whole family in the Audi.

And to make it worse some fectard had spilt diesel from Leek to Stone. 16 bum squeaking miles of it!

Post by **Kwacky** » 24 Apr 2016, 19:47

Thought about washing it and adjusting the chain, saw the rain, went back inside.

Post by **Kwacky** » 25 Apr 2016, 08:37

Left home with the sun out and clear blue skies. Arrived at work under dark skies, wind and freezing cold rain.

Post by **Blade** » 25 Apr 2016, 09:29

Monty wrote:Backed the rebound and compression off a turn on the front today and oddly the rear feels so much better.

Definitely getting quicker and getting a lot more feed back from the bike, especially in the slower corners.

I arrived at the bottom of Itchy's Leap at about 120, at least 30mph quicker than last time. Fortunately this time had the good sense to slam them on.

This bike just gets better and better.

Arrived at the bottom of Itchy's leap at 120.........

Where were you thinking of landing Staffordshire

Post by **Monty** » 25 Apr 2016, 09:51

Blade wrote:
Monty wrote:Backed the rebound and compression off a turn on the front today and oddly the rear feels so much better.

Definitely getting quicker and getting a lot more feed back from the bike, especially in the slower corners.

I arrived at the bottom of Itchy's Leap at about 120, at least 30mph quicker than last time. Fortunately this time had the good sense to slam them on.

This bike just gets better and better.
Arrived at the bottom of Itchy's leap at 120.........

Where were you thinking of landing Staffordshire

To be fair the bottom of Itchy's Leap is actually Staffordshire.

Post by **D41** » 25 Apr 2016, 15:49

I think he meant 1.20pm....

Post by **Kwacky** » 28 Apr 2016, 08:52

Froze my nuts off again. I'm sure these seasons are going backwards.

Post by **Kwacky** » 28 Apr 2016, 20:42

Got it wet. Very wet. Thunder and lighting on the way home.

Post by **Rossgo** » 29 Apr 2016, 05:52

Need to get an MOT soon and Aldo need to wash it after Skeggy it's really muddy may do this at weekend

Sent from my HTC One_M8 using Tapatalk

Post by **C00kiemonster** » 29 Apr 2016, 12:41

Prepped all the new parts for the missus's CBR600rr. Tomorrow I'm stripping the front callipers, new pads, replace brake fluid, Scrap chain and replace, new sprockets.

Post by **kingfixer** » 29 Apr 2016, 13:40

picked the 999 this morning in Wokingham, have new pads, grips and baffles waiting for it. The baffles are so I can get into castle Combe circuit as ive never done it and its really close to me.

Post by **kiwikrasher** » 29 Apr 2016, 23:06

Rossgo wrote:Need to get an MOT soon and Aldo need to wash it after Skeggy it's really muddy may do this at weekend

Sent from my HTC One_M8 using Tapatalk

Who's Aldo? have you kidnapped a little Italian immigrant for the sole purpose of cleaning your bike as you require?

Post by **Rossgo** » 30 Apr 2016, 07:03

kiwikrasher wrote:
Rossgo wrote:Need to get an MOT soon and Aldo need to wash it after Skeggy it's really muddy may do this at weekend

Sent from my HTC One_M8 using Tapatalk
Who's Aldo? have you kidnapped a little Italian immigrant for the sole purpose of cleaning your bike as you require?

Hahaha!! Well I nicked him when I went to Rome last year...I need to get him to work!!

Sent from my HTC One_M8 using Tapatalk

Post by **Frankie** » 30 Apr 2016, 15:48

Collected my bike this morning and all my gear from the Spain trip, started to strip the bike down already, rad off, now to shove all the dirty kit in the wash and unpack all the gear, while watching a good old classic, Smokey and the Bandit lol... love it.

Post by **C00kiemonster** » 30 Apr 2016, 16:00

C00kiemonster wrote:Prepped all the new parts for the missus's CBR600rr. Tomorrow I'm stripping the front callipers, new pads, replace brake fluid, Scrap chain and replace, new sprockets.

Well i got this done today, I've never changed a chain before, I've always taken it somewhere.

What a ball ache putting the new chain together - those fiddly o rings wouldn't stay still while i lined up the tool. Its done now, but god i need a drink!

Fettling with chain tension and final bleeding tomorrow, then I'm off for a few hours to bed in the brakes, tyres and chain

Post by **StMarks** » 30 Apr 2016, 16:19

C00kiemonster wrote:....What a ball ache putting the new chain together - those fiddly o rings wouldn't stay still while i lined up the tool. Its done now,,,

Bit late now, but fwiw I usually glue them into place with a drop of chain lube.

If it's your first one, did you make a note of the width of an assembled link, so that you pressed your side plate on "just enough" ,? -Rather than the frequent "too tight" first time attempt.?

Post by **C00kiemonster** » 30 Apr 2016, 16:23

StMarks wrote:
C00kiemonster wrote:....What a ball ache putting the new chain together - those fiddly o rings wouldn't stay still while i lined up the tool. Its done now,,,
Bit late now, but fwiw I usually glue them into place with a drop of chain lube.

If it's your first one, did you make a note of the width of an assembled link, so that you pressed your side plate on "just enough" ,? -Rather than the frequent "too tight" first time attempt.?

Chain lube helped, but the plate kept falling off. i needed 5 hands

In the end i put some thin tape around the middle between the rivets. Plus a lot of swearing

Yep - checked the plate was on enough to be the same width (2 goes to get it right). The rivets were not too bad - i just hope they are right - they should be as i couldn't tighten them any more physically and the links move with the same movement as the other 'proper' ones.

Still a PITA.

Post by **Blade** » 30 Apr 2016, 16:56

Cookie most manufacturers specify a diameter the rivet should spread too. If you can't source that info check the width is the same and the link is not tight and you should be fine. Knowing you mate I'm sure you've done a top job

Post by **C00kiemonster** » 30 Apr 2016, 19:52

Blade wrote:Cookie most manufacturers specify a diameter the rivet should spread too. If you can't source that info check the width is the same and the link is not tight and you should be fine. Knowing you mate I'm sure you've done a top job

Cheers chappie - I'll have a look. Its an Afam chain so it might give me some peace of mind as i don't want it flying off

Post by **Rossgo** » 30 Apr 2016, 20:38

This morning I have the bike a really good deep clean, all muck off it from the Skeggy trip, cleaned the chain and ACF50'd everything! Also changed my original (10 year old) number plate that was cracked and had 6, yes 6, holes in it with a brand spanking new one, it's surprising how a little change can make you fall in love with it all over again!!

Sent from my HTC One_M8 using Tapatalk

What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??

Re: What did you do to your bike today ??